Setting the targets for spring breeding 2021
Nationally only 65% of cows and heifers calve during the first six weeks of the calving season, ideally this should be at 90%. As part of Breeding Week 2021 the major factors to achieving a high six-week calving rate are discussed here
In pasture-based systems of milk production, the three-week submission rate target is 90% which is critical in order to achieve a six-week calving rate of 90%. Doing so facilitates long lactations and high levels of milk production.
While nationally this has improved over the past five years, our analysis shows that the effect on profitability is still substantial. On average the national cost is €206 less profit per cow per lactation. In the accompanying series of video clips presented by Dr. Stephen Moore, Teagasc Moorepark extracted from a recent webinar conducted by Teagasc on dairy breeding, we discuss the major factors to achieving a high six-week calving rate.
Maximising three-week in-calf rate
Two factors reduce three-week in-calf rate.
- Low submission rate –because cows are not cycling or because of poor heat detection;
- Low conception rate – because of the presence of uterine infection.
Between three and five weeks before the start of breeding, body condition score the whole herd and identify cows with a score of 2.5 or less. Such cows have a low submission rate and conception rate. They should be kept on once a day milking until three weeks after they have been bred.
The second step is to record the heats of cows before breeding starts using tail paint to identify cows that are not cycling. They should be scanned and non-cycling cows synchronised to breed them on mating start date. Cows that are less than 30 days calved are not suitable for synchronisation and should be left until a group is put together and a second non-cycling group synchronized later on e.g. three weeks into the breeding season.
Record dates of insemination on ICBF’s HerdPlus either manually or via the AI technician handhelds. This will allow you to run Fertility Reports. Targets are 30% inseminated in week 1; 60% submitted by the end of week 2; and, 90% submitted by the end of week 3.
In the accompanying three videos we will address methods of improving the three main causes of reduced three-week in-calf rate:
- Non-cycling cows;
- Poor heat detection;
- Uterine infection.
Treatment of non-cycling cows
Cows that are calved 30 days or more but not cycling should be synchronised to induce cyclicity. Details of the Teagasc Moorepark recommended protocol for synchronising heat in such cows is detailed in the following video clip.
Heat detection
Cows come into heat at all times of the day. On average however they are only on heat for 8 hours with slightly more than half of them standing for 8 hours or less. This makes them really difficult to identify in heat. Our research has also found that late calving cows will be more difficult to spot in heat as they tend to have shorter duration of standing heat and because they come into heat later in the breeding season (when the bulling group will be smaller).
As a result Teagasc recommends two actions:
- Three periods (or more) of heat detection daily (early morning, mid-day and late evening);
- That a heat detection aid or aids are used (such as tail paint and a vasectomised bull).
Metrichecking cows
The second factor associated with low three-week in-calf rate is low conception rate caused by uterine infection. Research at Teagasc Moorepark on identifying uterine infection is done using a Metricheck device.
Five grades of score are identified:
- Score 1: Clear mucus without pus – this indicates a healthy uterus;
- Score 2: Mucus with flecks of pus;
- Score 3: Mucus with <50% pus;
- Score 4: Mucus with ≥50% pus;
- Score 5: Mucus with ≥50% pus and odour.
Research at Teagasc Moorepark has shown that cows with a score of 2 or greater should be treated with an intrauterine antibiotic subject to veterinary advice to cure the infection and increase conception rates.
Find out all of the detail on Breeding Week here